I’m beginning to write the next update on my starship project. I thought I’d be done with the whole ship by now but I made it too big. The next project with be something a lot smaller. I’m thinking landspeeder this time…
- Vents below Tactical Bridge
- More Detail to the Dorsal Ridge
- Auxiliary Thrusters
- More Medium Turbolaser Cannons
- More Landing Struts to the Stern Section
- Vertical panels to various parts of the ship
- Shield Generators
- Proton Torpedo Tubes
- Maneuvering Thrusters
- Horizontal Heat Sinks along edges of ‘Wings’ and other edges of the same design Continue reading
Since the last update, I decided it was time to work on the Observation Deck which has been left neglected for far too long. At the time of this writing I have decided to rename the Observation Deck to the Tactical Bridge to better suit its purpose.
The purpose of the Tactical Bridge is mostly for strategizing during battles and the rest of the time it is used for observation. It gives a better view of the ship from more angles than it is possible from the Main Bridge. Since it is focused on battles, the inside of the Tactical Bridge is equipped with only a limited amount of controls unlike the Main Bridge that is set up to control all of the ship’s functions. Continue reading
In this update I am covering the work I have done to the Main Entrance Junction and the Cargo Bays since the last update I wrote. There are only 15 snapshots to look at this time because there just wasn’t much detail to show because the majority of the work was already done.
First thing I did was color in all of the parts in the Main Entrance Junction to match the color choices in the corridor sections of the ship. I thought about replacing the wall panels and dividers with the utility versions but I decided to leave it as it was because it isn’t just a work area of the ship, it’s the first thing passengers see when they board the ship when the ship is landed. Continue reading
Since the last update I decided to finish the engineering section before writing any updates and because of that there are 110 images in this post all related to the Engineering Section.
Here’s what was done:
- Matched the colors of the suspended catwalk to the catwalk in the Landing Bay.
- Changed all the wall panels to the utility wall panel design.
- Widened the rear tower to accommodate the Reactor Core.
- Designed and modeled Reactor and fuel storage tanks.
- Designed the Power Distribution Unit, power conduits and power consoles.
- Created ceiling lights based on Landing Bay.
- Designed Water Treatment Plant and Trash Incinerator.
- Merged the small controls rooms with the main room eliminating doors.
- Added computer consoles to room and created standing wall computer consoles.
- Designed the main computer racks and created moving maintenance platforms.
- Created utility wall boxes.
That distraction turned out to be a good thing because the Landing Bay is the largest single area of the ship. Most of the work was already done in the Landing Bay; it mostly needed its components colored in and for the ceiling detail to be added. I ended up doing a lot more than that and now it would be ready for starfighters and a certain familiar freighter to inhabit it. In its current configuration, it doesn’t accommodate as many starfighters as I would have liked but perhaps when the ship is complete I may work on different configurations for different applications of use. Continue reading
It’s been about 4 months since my last update on the ship’s progress but that’s because I have been busy working on other things. I could have written something a lot sooner except I decided to wait until I completely finished modeling the Bridge. Well, ‘completely’ might be an exaggeration because I will probably think of something else to add to it.
So, this time around I was able to do quite a bit. In the Helm section of the Bridge, I added computer consoles and a ceiling fixture. On the Main Bridge… I added computer consoles to the crew pits, designed a curved workstations with large tactical screens, designed controls for the doors and turbolifts on the ship, finished the docking ring airlocks, reconfigured the Bridge with regards to the Ready Room and Conference Room while finishing both rooms, changed out the entrance for the Bridge with something more substantial, added a Command Salon after shrinking down the Ready Room and finally created some star chart screens. Continue reading
In this update I will cover the work done on the Helm Section of the ship so far. The majority of the work was done on the pilot stations including the computer consoles, flight controls and the pilot seats. It might not seem like much but the work done here will be reflected in nearly all future computer consoles and work stations on the ship.
I am looking to make a unified design across the ship. Because the ship is intended to be new and in unused condition, there won’t be a mismatch of parts from different ships and manufacturers like the heavily worn and used ships like the Millennium Falcon or the Tantive IV.
That’s it, I’ve done it again by failing to write an update for a long time! Because of this I will be splitting the progress of the ship into two updates. In this update I will go over the progress of the Bridge interior and the next one to follow will be on the Helm.
It was about time that I started to work on the interior of the ship for a while. I decided on working on the Bridge which is one of the largest sections of the ship and possible the most highly detailed one.
I had done some work on the Bridge interior before but it mostly entailed the split level floor and putting in basic wall panels. The wall panel work, in the end, was pointless as now it has been completely redone. Continue reading
As I mentioned before, the escape pods were starting to bug me and the reason is that the entry doors are just too big to be swung open into the inside of the ship. Because the doors took up so much space when opened, I had to compromise the design of the escape pod launch rooms to accommodate them.
I wanted the escape pods to match those on the Tantive IV and at the same time match the general design of the escape pod access ports inside the ship. That was just not possible to do with the design of the escape pods seen in the movie. To get the launch rooms designed to my liking I decided to compromise on the design of the escape pods themselves.