Untitled Capital Ship Project Update 14

Since the last update I decided to finish the engineering section before writing any updates and because of that there are 110 images in this post all related to the Engineering Section.

Here’s what was done:

  • Matched the colors of the suspended catwalk to the catwalk in the Landing Bay.
  • Changed all the wall panels to the utility wall panel design.
  • Widened the rear tower to accommodate the Reactor Core.
  • Designed and modeled Reactor and fuel storage tanks.
  • Designed the Power Distribution Unit, power conduits and power consoles.
  • Created ceiling lights based on Landing Bay.
  • Designed Water Treatment Plant and Trash Incinerator.
  • Merged the small controls rooms with the main room eliminating doors.
  • Added computer consoles to room and created standing wall computer consoles.
  • Designed the main computer racks and created moving maintenance platforms.
  • Created utility wall boxes.

Continue reading

Untitled Capital Ship Project Update 13

At the end of the last update I said I would start finishing the corridor sections. I started to do that but then I got distracted and I began working to complete Landing Bay instead.

That distraction turned out to be a good thing because the Landing Bay is the largest single area of the ship. Most of the work was already done in the Landing Bay; it mostly needed its components colored in and for the ceiling detail to be added. I ended up doing a lot more than that and now it would be ready for starfighters and a certain familiar freighter to inhabit it. In its current configuration, it doesn’t accommodate as many starfighters as I would have liked but perhaps when the ship is complete I may work on different configurations for different applications of use. Continue reading

Untitled Capital Ship Project Update 12

It’s been about 4 months since my last update on the ship’s progress but that’s because I have been busy working on other things. I could have written something a lot sooner except I decided to wait until I completely finished modeling the Bridge. Well, ‘completely’ might be an exaggeration because I will probably think of something else to add to it.

So, this time around I was able to do quite a bit. In the Helm section of the Bridge, I added computer consoles and a ceiling fixture. On the Main Bridge… I added computer consoles to the crew pits, designed a curved workstations with large tactical screens, designed controls for the doors and turbolifts on the ship, finished the docking ring airlocks, reconfigured the Bridge with regards to the Ready Room and Conference Room while finishing both rooms, changed out the entrance for the Bridge with something more substantial, added a Command Salon after shrinking down the Ready Room and finally created some star chart screens. Continue reading

Untitled Capital Ship Project Update 11

In this update I will cover the work done on the Helm Section of the ship so far. The majority of the work was done on the pilot stations including the computer consoles, flight controls and the pilot seats. It might not seem like much but the work done here will be reflected in nearly all future computer consoles and work stations on the ship.

I am looking to make a unified design across the ship. Because the ship is intended to be new and in unused condition, there won’t be a mismatch of parts from different ships and manufacturers like the heavily worn and used ships like the Millennium Falcon or the Tantive IV.

Continue reading

Untitled Capital Ship Project Update 10

That’s it, I’ve done it again by failing to write an update for a long time! Because of this I will be splitting the progress of the ship into two updates. In this update I will go over the progress of the Bridge interior and the next one to follow will be on the Helm.

It was about time that I started to work on the interior of the ship for a while. I decided on working on the Bridge which is one of the largest sections of the ship and possible the most highly detailed one.

I had done some work on the Bridge interior before but it mostly entailed the split level floor and putting in basic wall panels. The wall panel work, in the end, was pointless as now it has been completely redone. Continue reading

Untitled Capital Ship Project Update 9

This is a short update because it involves just one big change: the escape pods.

As I mentioned before, the escape pods were starting to bug me and the reason is that the entry doors are just too big to be swung open into the inside of the ship. Because the doors took up so much space when opened, I had to compromise the design of the escape pod launch rooms to accommodate them.

I wanted the escape pods to match those on the Tantive IV and at the same time match the general design of the escape pod access ports inside the ship. That was just not possible to do with the design of the escape pods seen in the movie. To get the launch rooms designed to my liking I decided to compromise on the design of the escape pods themselves.

Continue reading

Untitled Capital Ship Project Update 8

Untitled Capital Ship Progress #9This time I managed to do exactly what I planned on doing. I changed the main weapon a bit; I added more details to the hull, changed the engine layout and created more weapons

[notice]I am trying out a new way to display the images in these updates. Now when you click on a thumbnail (when reading on JediCharles.com) a larger version will pop up and you then have the option to cycle through all the images contained in the update gallery. This will eliminate the need for the flash based gallery that I have been including in the blog posts.[/notice] Continue reading

Untitled Capital Ship Project Update 7

After working on the Bridge section for a while I felt the need to work on other parts of the ship.

This project may seem scatterbrain, but that is because it is. To prevent boredom I have to move on to something else to keep my creativity going. Typically those who design stuff like this sketch it out on paper first and make several revisions before they even start creating a prototype model let alone the final 3D model or a physical model. That method probably makes the most sense but in my case I am completely digital and it’s out of necessity.

I started off creating a general layout of the ship’s interior in Photoshop but after that I went straight to modeling. I only had a general idea of what the exterior design would be. Pencil sketches of my ideas would really help but instead I let my ideas evolve as I model. Some ideas just don’t work and that is evident in the design of the main weapon as you will see. Continue reading

Untitled Capital Ship Project Update 6

Once again I did a lot of work on the ship without writing one of these updates so there will be 2 updates. In this update I am focusing on the designing of the front entrance of the ship, the front landing gear and the main docking rings. In the next update I will be covering the rear landing gear, the buildup of the primary weapon and a few exterior details.

In order to accommodate a front entrance for the ship I added on to bottom of the bridge section giving the ship a “big chin”. The additional depth of the bridge section allowed me to extend the turbolift shaft to the new entrance. In addition to being the front entrance to the ship, the new bottom of the bridge serves as the front landing gear. Continue reading